What should I do to my e-foil right after riding?

Saltwater looks harmless, but to your e-foil, it’s one of the biggest threats to performance and longevity. If you want your board to last more than a season in Florida’s salt and sun, your post-ride routine matters.

After every session, you should follow this simple three-part maintenance process:

1. Rinse all major components with fresh water.
   
   Focus on the parts where salt collects and corrosion starts: your mast, prop, wings, battery, remote, and board handles. Even 30 seconds per part can flush away salt crystals and sand that eat away at metal.
   
   
2. Dry critical surfaces, especially anything metal.
   
   Use a clean towel to dry exposed screws, charging ports, battery pins, and the remote. Saltwater that evaporates on metal will leave behind corrosion. If water pools in hidden areas like wing screws or mast bolts, it can start damaging the hardware before your next ride.
   
   
3. Store it right.
   
   Never leave your gear wet, baking in the sun, or sealed inside a hot box. Keep your board in a shaded, ventilated spot. Lay your battery flat, not upright, and make sure your mast drains completely if it has an internal channel like the Waydoo Evo.

👉 Need a visual walkthrough of these steps? See the full maintenance video here.

How do you rinse saltwater off your Waydoo Evo?

Rinsing your Waydoo Evo isn’t just a good habit, it’s a critical step to prevent salt buildup, corrosion, and mechanical issues. Because the Evo uses saltwater as part of its cooling system, it’s especially important to flush key areas after each ride.

Here’s how to rinse it the right way:

Start with the mast

The mast on the Evo includes a hollow internal channel that pulls saltwater through during your ride. If that channel isn’t flushed, salt crystals and debris will settle inside and start corroding the metal from within.

• Locate the small hole near the base of the mast.
  
  
• Spray fresh water into the opening for at least 30 seconds.
  
  
• Watch for clean water exiting the other side — that’s your sign it’s clear.
  

This step alone can prevent a ton of long-term damage, especially if you’re riding multiple times a week in places like Miami, the Keys, or the Gulf.

Rinse all connection points and exposed metal

Pay attention to:

• The mast-to-board junction
  
  
• The rear wing screws and plate
  
  
• The propeller and inside the prop guard
  
  
• The bolts around the fuselage
  
  

Use a garden hose or clean water bottle, nothing high-pressure, and let the water flow naturally over each part. Don't rush it. Just a slow rinse is more effective than blasting it.

Hit the board handles and screw areas

The Waydoo’s EPP board has recessed handles that hide small metal screws. Rinse both the top and bottom handles, especially underneath where saltwater can collect unnoticed.

No need for soap or sprays

Unless your gear is unusually grimy, fresh water is enough. Household cleaners or harsh sprays can actually damage the foam or electronics. If you do want a cleaning product, use something designed for marine electronics or e-foil gear.

✅ Quick Tip: Rinse anything that moves, anything metal, and anywhere two parts meet. That’s where salt does the most damage.

👉 Want to go step-by-step through this? Our complete care guide covers rinsing, drying, and storage in detail.

How to clean and care for your e‑foil remote

The remote might be small, but it’s one of the most failure-prone parts of your e‑foil if you don’t rinse it properly. Saltwater sneaks into the trigger and buttons fast, especially in South Florida’s hot, windy conditions, and it doesn’t take much to cause sticky triggers or connectivity glitches.

Here’s how to keep your Waydoo Evo remote in top shape:

1. Rinse with fresh water every time.
   
   Hold the remote with the trigger facing down and gently spray with fresh water. Let it flow over the trigger, button edges, and seams. This clears out salt and sand without forcing moisture deeper inside.
   
   Avoid using high-pressure hoses or soaking the remote — it’s water-resistant, not waterproof.
   
   
2. Skip the soap
   
   Fresh water is enough for daily cleaning. Household soaps can leave residue or degrade the remote’s seals. If you need a deeper clean, stick with products designed for marine electronics.
   

    

   Our Waydoo maintenance guide covers approved sprays and safe cleaning habits.
   
   
3. Use silicone spray but sparingly
   
   Every few sessions, a light silicone spray can help keep the trigger action smooth. Just make sure everything is dry first, and don’t overdo it — too much lubricant can attract dust and gum things up.
   
   
4. Dry before storing
   
   After rinsing, shake off excess water, towel-dry the seams, and store your remote in a shaded, well-ventilated area. Never leave it in a sealed, wet gear bag — that’s how corrosion starts.

Pro Tip: If your remote ever feels sluggish or fails to connect, start with a deep rinse and dry before assuming it’s a tech issue.

Why fresh water rinsing is critical for mast, prop, and screws

If you’re only giving your mast and prop a quick splash after riding — you’re missing the spots where salt does real damage.

Here’s how to protect the most exposed, high-stress components on your e‑foil:

Flush the mast channel

The Waydoo Evo pulls saltwater through the mast during operation. After each session, find the small hole at the base of the mast and spray fresh water directly into it for 30 seconds. You’ll usually see salt crystals or sand drain out the other side — especially after choppy days.

The internal channel is one of the most overlooked areas of post-ride care. Skipping it leads to long-term corrosion that’s easy to prevent with a simple rinse.

We walk through this step visually in the Waydoo Evo Buyer’s Guide, and explain why this board is easier to maintain than most.

Hit the fuselage and wing connection points

Even if you leave the wings on, rinse around the screws and the rear wing plate. These seams trap salt that dries into fine white powder — a sign that corrosion is already starting.

If you remove the wings, it’s a great opportunity to apply a small dab of silicone grease to the hardware — just don’t overdo it. Our article on healthy charging and connection habits has crossover tips for any contact points on the board.

Clean the prop and guard thoroughly

The prop area catches salt, weeds, and line. Rinse the blades and inside the guard until the prop spins freely with no grit. This step takes seconds — but skipping it can lead to unnecessary friction or noise next time you ride.

Towel-dry any metal hardware

Even after a fresh water rinse, towel drying is key. This includes mast bolts, wing screws, and the base of the fuselage. Letting saltwater air dry on metal is the #1 cause of slow-building corrosion in newer rider setups.

Want to know how the board’s EPP foam handles wear and water? We tested it thoroughly in our blog: Is the EPP E-Foil Durable?

How do you clean e-foil battery connectors safely?

Your battery does more than power your ride — it’s the heart of your e‑foil system, and also one of the most expensive parts to replace. That’s why rinsing and drying the connectors properly after each session is non-negotiable.

In our video walkthrough on daily maintenance, Chris shows exactly how we rinse the Waydoo Evo battery at the shop after every ride. Here’s the breakdown in writing so you can follow along step-by-step:

Rinse gently — don’t soak

Use a clean hose or water bottle to spray around the connector pins, push buttons, and edges of the battery casing.

• Press the buttons a few times while rinsing — this helps dislodge salt from the crevices.
  
  
• Hold the battery at a slight tilt so water runs off instead of pooling.
  

Never dunk the battery in water — it’s sealed against splashes, not submersion.

Dry completely before charging

Water left inside the connector port can trigger error codes or damage your charger.

• Use a towel to gently pat around the pins and buttons.
  
  
• Let the battery sit for 10–15 minutes in a shaded, breezy spot before plugging anything in.
  
  
• If needed, use a soft blower or fan to speed things up.
  
  

For full charge-cycle tips, check out our post on Waydoo Healthy Charging Mode.

Store it flat and unplugged

Never store your battery fully charged or completely empty. Aim for a 60–70% charge when putting it away, and always lay it flat or slightly angled so any water drains out.

For longer downtime or travel prep, we’ve covered this in detail in our battery storage guide — a must-read for South Florida riders especially.

Check for signs of wear

After rinsing and drying, take a quick look at the metal contact points.

• If you see any green corrosion, white salt crust, or unusual discoloration — don’t plug in.
  
  
• Give it another rinse and dry, or contact us before charging.
  

Not sure what to look for? Pause the video at the 1:55 mark — Chris shows what clean, healthy connectors should look like on a Waydoo Evo battery.

Need battery tips? Learn how to properly charge your Waydoo Evo in our How to Charge Waydoo Evo Battery guide.

Not sure how to store your battery long-term? Check out How Do I Store My Waydoo Battery for storage tips that keep your battery in top shape.

What’s the best way to store your e‑foil between sessions?

Rinsing is only half the battle. Even the cleanest board can suffer damage if it’s stored the wrong way, especially in a hot garage or sealed gear bag with leftover moisture.

In our daily maintenance video, we walk through the exact storage steps we follow at E-Foil Miami after every ride. Here’s the full checklist so you can do the same.

Bring your gear out of the elements

• Store your remote, battery, and mast indoors, away from salt air and direct sun.
  
  
• The board itself (especially Waydoo’s EPP foam) can handle the heat better, but avoid stacking heavy gear on top or sealing it wet in a bag.
  

Want to know how tough the foam actually is? See Is the EPP E-Foil Durable?

Lay the battery flat — not upright

This one matters more than most riders realize. If there’s even a drop of water left near the battery connectors, storing it upright can let moisture settle in the wrong places.

• Instead, store the battery flat or slightly angled, so gravity helps it drain.
  
  
• And never charge a battery while it’s still wet — see our full battery storage tips if you need a refresher.
  

Don’t store the mast vertically

Waydoo Evo’s mast has a hollow center channel that moves water during your ride. If you stand the mast up after rinsing, that water can collect and cause internal corrosion.

• Store it horizontally or hang it upside down so water can drip out completely.
  
  
• We cover this trick in the Waydoo Evo Buyer’s Guide and video as well — it’s one of the best habits to prevent unseen damage.
  

Let everything drip-dry before packing

Even if you're in a hurry, give your gear a few minutes to air out.
Waydoo’s EPP foam dries quickly, but if water gets trapped in seams or bolt holes, it can cause rust or mold in enclosed spaces.

Quick tip from the video: Just lean your board on a wall in a shaded spot while you rinse the rest. By the time you're done, it’s mostly dry and ready for transport.

Common e-foil maintenance mistakes riders make

Most damage we see on customer gear doesn’t come from crashing — it comes from skipping the basics. A lot of riders are surprised to find corrosion, sticky triggers, or power loss after just a few months… but it’s usually preventable.

Here are the most common mistakes we see — and how to avoid them:

Skipping the rinse entirely

Sounds obvious, but it happens. You pack up fast, get distracted, and leave the board salty until next time.

• Even a quick rinse within 30 minutes of riding can stop corrosion in its tracks.
  
  
• If you’re not sure what to rinse, rewatch the maintenance video guide — or print our checklist at the bottom of this blog.
  

Letting saltwater air-dry on metal

This is one of the fastest ways to rust screws, wing bolts, and battery pins.

• Always towel dry your connectors and hardware. It takes 2 minutes and adds months to your gear life.

We talk more about which parts to focus on in our  complete care guide.

Over-greasing wing connections and mast joints

Yes, a little silicone grease helps prevent wear — but too much traps dust, sand, and grime.

• Apply a light layer every few sessions, not after every ride.
  
  
• Wipe away excess before storing.
  
  

Charging before drying

We see this one often: a battery looks dry on the outside, but water inside the connector port causes a short.

• Never plug in right after rinsing.
  
  
• Let your battery sit for at least 15 minutes, or use a blower on low heat if you're in a rush.
  
  

Storing the mast or battery upright

This allows leftover water to settle inside the very parts you're trying to protect.

• Always lay these flat or upside down after rinsing.

Do these post-ride steps apply to Lift, Fliteboard, and other e‑foils?

Yes, absolutely. Whether you’re riding a Waydoo Evo, a Fliteboard, or a Lift, saltwater doesn’t care what brand you ride. The basics of daily maintenance stay the same across the board:

• Fresh water rinsing
  
  
• Drying battery connectors and metal hardware
  
  
• Storing gear properly between sessions
  
  

We’ve used all three systems at E-Foil Miami, and while each has its own quirks, the core care steps are nearly identical. Propeller guards, wing screws, battery contacts, and mast seams are vulnerable on every model.

That said, the Waydoo Evo stands out in how beginner-friendly and accessible it makes maintenance:

• Tool-free setup
  
  
• Easy-to-rinse battery design
  
  
• Simple mast channel to flush
  
  
• Durable EPP foam board that dries quickly
  
  

In our Waydoo Evo Buyer’s Guide, we break down what makes the Evo more manageable than higher-end boards that require complex teardown just to rinse connectors.

If you're more of a visual learner, the daily maintenance video shows how quickly we run through the rinse and dry routine: no special tools, no overthinking.

No matter what you ride, the rule is simple: rinse, dry, and store with care. Small steps now save big headaches later.

Tips for Waydoo Evo riders to prevent corrosion

If you’re riding the Waydoo Evo, you’ve already got a head start, the board is built with post-ride care in mind. But there are a few Evo-specific tricks that go beyond the basics and make a big difference in long-term durability.

These are the exact habits we use at E-Foil Miami after every demo and lesson.

1. Flush the mast channel every time

The hollow mast is one of the Evo’s cleverest features, but it also collects salt if left unchecked.

• After rinsing the outside, spray fresh water into the mast hole near the base for 30 seconds.
  
  
• You’ll often see sand or salt crystals flush out the other side.
  
  
• See it done in the video if you’re not sure where to aim the hose.
  
  

2. Rinse and dry battery connectors carefully

Because the Evo battery has more exposed metal than older models, it’s even more important to press the buttons under water flow, towel the contact pins, and let it dry before charging.

Want a full battery storage walkthrough? Read How to Store Your Waydoo Battery

3. Towel-dry high-risk metal areas

Waydoo boards don’t require disassembly after every ride — but you should always hit these spots with a dry cloth:

• Wing screws and plates
  
  
• Mast base bolts
  
  
• Battery contact pins
  
  
• Remote trigger edges
  
  
• Handle screw pockets on the board
  
  

These spots often hide saltwater droplets that turn corrosive once they evaporate.

4. Don’t overdo silicone grease

A small amount of silicone on mast or wing joints helps protect against friction and oxidation — but too much turns into a dust magnet.

• Apply a light film every few sessions, then wipe off any excess before storing.
  
  

5. Relax — the foam is built to last

The Evo’s EPP construction is highly impact-resistant and water-shedding.
You don’t need to baby it like you would a carbon board.

We tested the limits of the material in this blog on EPP durability — and yes, it passed.

Still unsure if you’re doing it right? Stop by the shop or book a private demo — we’ll walk you through the full rinse routine and show you what to check.

Tools and products that make e‑foil maintenance easier

You don’t need a workbench full of gadgets to take care of your e‑foil — but having a few simple tools on hand can make rinsing, drying, and storing your gear way faster (and safer).

Here are the items we keep at E-Foil Miami for everyday board care:

Silicone spray (marine-safe)

Used sparingly, silicone spray helps protect metal threads, mast joints, and wing screws from friction and corrosion.

• Don’t use it every ride — just once every few sessions.
  
  
• Avoid contact with electronics or battery pins.
  
  
• Look for marine-grade, non-sticky formulas that won’t attract sand.
  
  

We touch on where and how to use it in the Waydoo Healthy Charging Mode guide, especially when protecting connector hardware.

 Low-heat blower or small fan

These are a game changer if you want to speed up drying without leaving your battery or remote exposed to the sun.

• Use after rinsing connectors, mast bases, or remote buttons.
  
  
• A low-end camera blower or USB fan works great — no need to overthink it.
  
  

Clean microfiber towels

Saltwater leaves residue even after rinsing — drying your metal components with a soft towel helps prevent corrosion before it starts.

Keep one towel for your board/gear, and another for the battery and remote.

Small tool pouch or kit

You don’t need to disassemble your setup daily, but it helps to carry:

• A spare wing screw or hex key
  
  

• A dry bag for your remote
  
  

• A small tube of silicone grease
  
  

Stashing these in your ride bag keeps you from scrambling post-session.

Want to see what this gear looks like in action? We show most of it in the daily maintenance video — and everything we use is easy to find at a marine store or online.

Should I dry charge my Waydoo battery?

Short answer: yes, but only after it's fully dry. Charging your e-foil battery while it's still damp is one of the most common causes of long-term damage. Even if the outside looks fine, moisture inside the connector port can short the contacts or trigger error codes.

Here’s how to handle it right:

Always dry first — inside and out

• After rinsing, towel off the battery housing and connector area.
  
  
• Press the power and pairing buttons a few times while drying to push out any hidden moisture.
  
  
• Let it sit in a ventilated space for 10–15 minutes minimum — longer if it's humid or overcast.
  
  

We use a small blower at E-Foil Miami to accelerate this step and Chris shows the full drying routine in our Waydoo maintenance video.

Charge only in a shaded, cool area

Once it’s dry, plug it in where there’s good airflow and no direct sun.

• Avoid hot garages, damp basements, or sealed cases.
  
  
• If you hear buzzing, see error lights, or smell anything unusual — unplug immediately.
  
  

We dive deeper into charging conditions, ideal percentages, and best practices in the Waydoo Healthy Charging Mode guide.

Don’t store fully charged or completely empty

If you're not riding for a few days, charge your battery to around 60–70%, then disconnect and store flat. Full storage tips (including angle and moisture guidance) are available in the How do I store my Waydoo Battery? and How to Charge Waydoo Evo Battery? blog.

Can E‑Foil Miami help with e‑foil care or parts?

While we don’t offer full service or repair shop work, we’re always here to help you ride smarter and protect your gear. Whether you're trying to troubleshoot a battery warning, figure out if your board’s making a weird sound, or just want someone to walk you through the rinse routine again — we’ve got your back.

At E‑Foil Miami, we ride year-round in some of the saltiest, sandiest conditions in the U.S. So we’ve seen almost every issue a board can throw at you — and we’re happy to share what we’ve learned.

If something doesn’t feel right:

• Call Chris directly. He’s helped dozens of riders solve gear issues over the phone, and usually spots problems faster than your manual.
  
  
• Bring your setup by the shop. Even a quick look at your connectors or mounting points can reveal if you’re missing something in your care routine.
  
  
• Book a private lesson if you want in-person help learning how to clean, rinse, and store your gear the right way.
  
  

Still figuring out which e‑foil is the best fit for your riding style or maintenance comfort level? The Waydoo Evo Buyer’s Guide breaks down exactly what you can expect from setup to rinse down.

And if you’d rather see everything done in real time, our maintenance video walks you through the process we follow at the shop after every single ride.

FAQ: E‑Foil Rinsing, Drying & Storage After Every Ride

Should I take my e‑foil apart after every session?

Not necessarily. If you’re riding multiple days in a row, you can leave your mast and wings attached, just be sure to rinse all connection points, especially the wing screws and mast base. If you go several sessions without disassembling, remove the wings and flush any hidden salt or grit.

Can I use soap or sprays to clean my e‑foil?

Stick with fresh water for everyday rinsing. If needed, a marine-safe electronics cleaner can help with built-up grime, but avoid household soaps. They often leave residue or react with metal parts. Check our e‑foil maintenance guide for safe product suggestions.

How should I store my battery if I’m not riding for a while?

Dry it thoroughly, store it flat, and keep it around 60–70% charged. Avoid sealed boxes or hot garages. For more detail, read How to Store Your Waydoo Battery.

Is it okay to leave my board out in the sun?

Short periods are fine, but avoid direct sun for extended periods, especially after rinsing. Water can heat up and warp components or accelerate corrosion. Let your gear dry in a shaded, breezy area instead.

What if I forget to rinse it one day?

Don’t panic, but don’t make it a habit. Rinse and dry it as soon as you remember. If you see any signs of crust, corrosion, or error codes, reach out to us. We’ll help troubleshoot.

our Post-Ride Routine Starts Here

Whether you’re new to the sport or already logging sessions weekly, a solid rinse and storage routine keeps your e‑foil performing like new.

• Need help with your gear? Stop by the shop or give us a call — we’re always happy to walk you through setup, care tips, or common troubleshooting.
  
  
• Still deciding which e‑foil is right for you? Start with the Waydoo Evo Buyer’s Guide 
  
• Prefer to see it in action? Watch our maintenance video here →
  
  

And if you’re ever unsure call Chris. We’d rather answer your question now than help you fix a problem later.